Anti-condensation Motor Heater MSHex
| Product Description | Anti-condensation Motor Heater MSHex |
| Product Type | 27-1776-. ..000.. |
| Brand | Bartec |
- Silicone-free
- Self-limiting
- Other length on request
Description
This flexible heating cable is used in explosive atmospheres to heat electric motors and generators at standstill. It provides reliable protection against corrosion damage and the associated mechanical breakdowns because it effectively prevents condensation from forming, even under extreme conditions.
The heater is supplied ready to connect, which is done via an M20 screwed cable connection fed into an Ex e distributor, or is directly clamped to terminals in an Ex room without a screwed connection.
As these heating cables are self-limiting, overheating is prevented, even if they are laid on top of each other. An additional temperature limiter is not required.
Structure of the heating cable
Copper power conductor wire 1.2 mm², nickel-plated
Self-limiting plastic heating element
Insulation sleeve made of FEP
Tin-plated copper braiding
Protective sleeve made of FEP
Technical Data
| Dimensions | see data sheet Bending radius: ≥ 25 mm |
| Material | Heating elements: CuNi or NiCr Insulation: alkali-free glass-fibre with silicone rubber |
| Heat output | 12.5 W, 25 W, 50 W, 75 W or 100 W Watts density 50 W/m at nominal voltage |
| Voltage | standard 230 V (special 110 V, others on request) Permissible excess voltage: 1.2 x nominal voltage Test voltage: 2000 V to earth |
| Connection | 2 x FEP-insulated stranded, copper flex, 0.5 mm² with crimped sleeve |
| Ambient temperature | Temperature range: -50 °C up to +180 °C |
Explosion Protection
| Marking | Ex II 2G Ex e IIC 200 °C (T2), T3 Gb |
| Certification | KEMA 08ATEX0109 IECEx KEM 09.0082 IEE 11.0276 |
| Datasheet |  |
| Operating Instructions | |
- General Info
-
Description
This flexible heating cable is used in explosive atmospheres to heat electric motors and generators at standstill. It provides reliable protection against corrosion damage and the associated mechanical breakdowns because it effectively prevents condensation from forming, even under extreme conditions.
The heater is supplied ready to connect, which is done via an M20 screwed cable connection fed into an Ex e distributor, or is directly clamped to terminals in an Ex room without a screwed connection.
As these heating cables are self-limiting, overheating is prevented, even if they are laid on top of each other. An additional temperature limiter is not required.Structure of the heating cable
Copper power conductor wire 1.2 mm², nickel-plated
Self-limiting plastic heating element
Insulation sleeve made of FEP
Tin-plated copper braiding
Protective sleeve made of FEP - Technical Data
-
Technical Data
Dimensions see data sheet
Bending radius: ≥ 25 mmMaterial Heating elements: CuNi or NiCr
Insulation: alkali-free glass-fibre with silicone rubberHeat output 12.5 W, 25 W, 50 W, 75 W or 100 W
Watts density 50 W/m at nominal voltageVoltage standard 230 V (special 110 V, others on request)
Permissible excess voltage: 1.2 x nominal voltage
Test voltage: 2000 V to earthConnection 2 x FEP-insulated stranded, copper flex, 0.5 mm² with crimped sleeve Ambient temperature Temperature range: -50 °C up to +180 °C - Explosion Protection
-
Explosion Protection
Marking Ex II 2G Ex e IIC 200 °C (T2), T3 Gb Certification KEMA 08ATEX0109
IECEx KEM 09.0082
IEE 11.0276 - Download
-
Datasheet Operating Instructions
