Anti-condensation Motor Heater MSHex
| Product Description | Anti-condensation Motor Heater MSHex |
| Product Type | 27-1776-. ..000.. |
| Brand | Bartec |
- Silicone-free
- Self-limiting
- Other length on request
Description
This flexible heating cable is used in explosive atmospheres to heat electric motors and generators at standstill. It provides reliable protection against corrosion damage and the associated mechanical breakdowns because it effectively prevents condensation from forming, even under extreme conditions.
The heater is supplied ready to connect, which is done via an M20 screwed cable connection fed into an Ex e distributor, or is directly clamped to terminals in an Ex room without a screwed connection.
As these heating cables are self-limiting, overheating is prevented, even if they are laid on top of each other. An additional temperature limiter is not required.
Structure of the heating cable
Copper power conductor wire 1.2 mm², nickel-plated
Self-limiting plastic heating element
Insulation sleeve made of FEP
Tin-plated copper braiding
Protective sleeve made of FEP
Technical Data
| Dimensions | Size of heating cable diameter: 10.2 mm x 4.8 mm Bending radius: ≥ 25 mm |
| Heat output | 12 W, 24 W, 48 W and 96 W (at 10 °C) at a specific heating output of 45 W/m |
| Voltage | Nominal voltage: 208 V to 254 V or 110 V to 120 V Insulation testing: AC 1500 V for 1 minute |
| Connection | Terminal wires with FEP isolation fine-stranded with tin-plated copper wires 1.5 mm², green and yellow protective earth conductor 2.5 mm² |
| Ambient temperature | switched on (energised) -40 °C up to +120 °C switched off -40 °C up to +170 °C |
Explosion Protection
| Marking | Ex II 2G Ex e IIC 200 °C (T2), T3 Gb |
| Certification | KEMA 08ATEX0109 IECEx KEM 09.0082 IEE 11.0276 |
| Datasheet |  |
| Operating Instructions | |
- General Info
-
Description
This flexible heating cable is used in explosive atmospheres to heat electric motors and generators at standstill. It provides reliable protection against corrosion damage and the associated mechanical breakdowns because it effectively prevents condensation from forming, even under extreme conditions.
The heater is supplied ready to connect, which is done via an M20 screwed cable connection fed into an Ex e distributor, or is directly clamped to terminals in an Ex room without a screwed connection.
As these heating cables are self-limiting, overheating is prevented, even if they are laid on top of each other. An additional temperature limiter is not required.Structure of the heating cable
Copper power conductor wire 1.2 mm², nickel-plated
Self-limiting plastic heating element
Insulation sleeve made of FEP
Tin-plated copper braiding
Protective sleeve made of FEP - Technical Data
-
Technical Data
Dimensions Size of heating cable diameter: 10.2 mm x 4.8 mm
Bending radius: ≥ 25 mmHeat output 12 W, 24 W, 48 W and 96 W (at 10 °C)
at a specific heating output of 45 W/mVoltage Nominal voltage: 208 V to 254 V or 110 V to 120 V
Insulation testing: AC 1500 V for 1 minuteConnection Terminal wires with FEP isolation
fine-stranded with tin-plated copper wires 1.5 mm²,
green and yellow protective earth conductor 2.5 mm²Ambient temperature switched on (energised) -40 °C up to +120 °C
switched off -40 °C up to +170 °C - Explosion Protection
-
Explosion Protection
Marking Ex II 2G Ex e IIC 200 °C (T2), T3 Gb Certification KEMA 08ATEX0109
IECEx KEM 09.0082
IEE 11.0276 - Download
-
Datasheet Operating Instructions